Configuring a McAfee ePO Server

Firmware: Microsoft ePO 3.5, 3.6, 4.0, and 4.6.7

Collector: Network Collector (SNMP)

Configuring a McAfee ePO 3.5 or 3.6 Server

To configure a McAfee ePolicy Orchestrator (ePO) 3.5 or 3.6 server to send log messages to TLC:

1. Select Start > Program Files > Network Associates > ePolicy Orchestrator 3.x Console
2. In the left pane, select McAfee Security > ePolicy Orchestrator.
3. Under Global Task List, select Log on to server.
4. In the Log On to Server dialog, enter the username and password for a valid ePolicy Orchestrator user account and click OK.
5. In the left pane, select: 

McAfee Security > ePolicy Orchestrator > [epo_server] > Notifications

where [epo_server] is the name of the ePO server.

6. In the Configuration tab of the Notifications dialog, select SNMP Servers.
7. In the SNMP Servers dialog, click Add.
8. In the Add or Edit SNMP Server dialog:
a. Enter the host name of your SNMP server in the Name field.
b. In the Server Address field, enter the IP address of your TLC Primary Manager and click OK.
9. In the Rules tab of the Notifications dialog, edit each rule so that all notifications are sent to the SNMP server.
a. Select the rule.
b. In the Describe Rule wizard, click Next.
c. In the Set Filters page, select Edit Notification Rule > 3. Set Thresholds.
d. Verify the Aggregation and Throttling values are set, and then click Next.
e. In the Create Notifications page, click Add SNMP Trap.
f. From the SNMP server drop-down in the Rules tab of the Add or Edit SNMP Trap dialog, select the SNMP server of the TLC Manager that will collect log messages from the McAfee ePO server.
g. In the Variables to include region, select the check boxes for all variables and click Save.The SNMP trap is added to the list of notifications for the selected rule.
h. Click Finish.
i. Repeat the steps above for each rule.

Configuring a McAfee ePO 4.0 Server

To configure a McAfee ePolicy Orchestrator (ePO) 4.0 server to send log messages to TLC:

1. Select Start > Program Files > Network Associates > ePolicy Orchestrator 4.x Console
2. In the left pane, select McAfee Security > ePolicy Orchestrator.
3. Under Global Task List, select Log on to server.
4. In the Log On to Server dialog, enter the username and password for a valid ePolicy Orchestrator user account and click OK.
5. Click Automation.
6. In the SNMP Servers tab of the Automation dialog, click New SNMP Server.
7. In the New SNMP Server dialog:
a. Enter the host name of your SNMP server in the Name field.
b. In the Server Address field, enter the IP address of your TLC Primary Manager and click OK.
8. In the Notification Rules tab of the Automation dialog, edit each rule so that all notifications are sent to the SNMP server.
a. Select the rule. (page appears.)
b. In the Describe Rule wizard, click Next.
c. In the Set Filters page, select Edit Notification Rule > 3. Set Thresholds.
d. Verify the Aggregation and Throttling values are set, and then click Next.
e. From the SNMP server drop-down, select the SNMP server of the TLC Manager that will collect log messages from the McAfee ePO server.
f. In the Variables to include region, select the check boxes for all variables and click Next.
g. Click Save to add the SNMP trap to the list of notifications for the selected rule.
h. Click Finish.
i. Repeat the steps above for each rule.

Next

If you are performing initial configuration of your TLC environment, see Configuring your TLC Environment.

Otherwise, see Adding a Monitored Asset for a new Log Source.

Configuring a McAfee ePO 4.6.7 Server

To configure a McAfee ePolicy Orchestrator (ePO) 4.6.7 server to send log messages to TLC:

1. Select Start > Program Files > McAfee > ePolicy Orchestrator 4.6.7 Console
2. In the Log On to ePolicy Orchestrator dialog, enter the User name and Password for a valid ePolicy Orchestrator user account and click OK.
3. In the Menu panel, select Configuration > Registered Servers.
4. In the lower-left corner of the Registered Servers dialog, click New Server
5. In the Description page of the Registered Server Builder wizard (see Figure 59):
a. Select SNMP Server from the 'Server type' drop-down.
b. In the Name field, enter the host name of your SNMP server.
c. (Optional) In the Notes field, enter a description of the server.

Figure 59.  Description page in the Registered Server Builder wizard

Description page

6. In the Details page of the Registered Server Builder wizard (see Figure 60):
a. In the Address fields, select IPv4 from the drop-down and enter the IP address of your TLC Primary Manager or McAfee ePO Log Source.
b. Select an SNMP Version, complete the related fields. (For further details, see the ePolicy Orchestrator online help.)
c. Click Send SNMP Trap.

ePolicy Orchestrator sends an SNMP trap to the TLC Manager. In the Real-Time Event Viewer in your TLC Console, confirm receipt of the trap.

d. Click Save to close the Registered Server Builder.

Figure 60.  Details page in the Registered Server Builder wizard

Details page

7. In the Menu panel, select Automation > Automatic Responses.
8. Complete the following steps for each of your Automatic Responses.
a. In the Actions column of the Automatic Responses dialog, select the response's Edit link.
b. In the Aggregation tab of the Response Builder dialog (see Figure 61):

Select Trigger this response for every event.

Select the Throttling check box and set the throttling interval.

Figure 61.   Aggregation tab in the Response Builder dialog

Aggregation tab

c. In the Actions tab of the Response Builder dialog (see Figure 62):

Select Send SNMP Trap from the drop-down.

In the SNMP Servers field, select the new SNMP server.

Move all values from the Available Types field to the Selected Types field.

Click Save.

Figure 62.   Actions tab in the Response Builder dialog

Actions tab

Next

If you are performing initial configuration of your TLC environment, see Configuring your TLC Environment.

Otherwise, see Adding a Monitored Asset for a new Log Source.